“The foundation of your home is your walls. The weather out there will not be nice and you need to pay special attention to your house’s exterior walls. It isn’t enough to paint the wall to make it waterproof. After dealing with rain, snow, wind, dust, and heat of the outside environment, the paint will start peeling off regardless of how expensive it is.”
Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.
Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.
Step 1: Properly expose the outside part of the wall
To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.
Step 2: Thoroughly clean the walls
A lot of dust and dirt is carried by air and sticks onto the outer part of the wall. To ensure the efficiency of the entire process, you need to clear the debris and dust thoroughly. The dirt and debris should be cleaned with a broom, brush, or sandpaper. Then rinse it off with a power washer.
Step 3: Check out for the cracks and fill them up
Cracks and holes can develop over time on your exterior walls. Follow up the cleaning process with a thorough look at the cracks and holes on your wall to ensure proper weatherproofing. They should be filled up with cement.
Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.
All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.
Inside the cracks, the cement mixture seals them properly. Make sure you remove all the loose cement from the wall before applying the cement.
Step 4: Add a layer of cement waterproofing sealer
If you want to make sure your wall is waterproof, you need to apply cement. After applying the cement in the crevices, let it dry and then apply the waterproof paint on the walls. Allow it to become dry after that.
Step 5: Pick the right water-proofer
There are many waterproof products available in the market. You need to pick the right one for your wall. The water-proofer should be chosen based on whether the wall is concrete or silicate.
A silicate-based concrete sealer is one of the options you can choose from. Pick a plaster waterproof Additive to add strength to your walls.
Step 6: Apply the water-proofer
You can apply the water-proofer with a roller or brush. If you want to apply more than one coat, give a thin coat first. Allow the first coating to dry before adding the second one.
Step 7: Apply tar and heavy-duty membrane
If you want to add more strength to the layer, you need to use a tar-based pitch. You can apply it on the wall.
If you want to waterproof your walls, you need to apply a heavy-duty plastic or rubber membrane after that.
Step 8: Consider adding gravel
A proper base for the trench is below the footer. The drainage pipes are going to get adequate support from a 34-inches gravel base. Gravel is long- lasting and provides better protection.
You need to lay the drainage pipe-cover with gravel. Next to the footer, level the position of the gravel and then back-fill it. The pipe should be covered for at least 3 inches.
Step 9: Add a fabric barrier
Along with a fabric barrier, secure the pipe. A fabric barrier will prevent the formation of dirt and keep your system clean. Simply back-fill the trench and build the top of the dirt relatively high and allow it to settle for a while. Slope the ground away from the walls for the run-off after youTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkiaTrademarkia isTrademarkia isTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia is
Conclusion:
Good waterproof gives your home a new life and strength to deal with outside weather issues. Magicrete can help you with good solutions for your walls. At a very low and affordable price, Magicrete can provide you with proper weatherproofing.
“It’s not like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s”
